| | |
Dri-Eaz DriForce®
The DriForce forces high-pressure air into wet walls for wall drying with minimal disruption. You only need to make tiny 1/4-inch holes at baseboard level to introduce 60 inches of static pressure from the DriForce! It's perfect for hard-to-reach areas like behind cabinets, tubs, under stairwells, etc.
| | Dri-Eaz Rescue Mat System
Dry out water-damaged hardwoods from above! The Rescue Mat System uses the power of a high-pressure blower like the DriForce to vacuum water vapor right through the surface of the floor. Two different sizes make it easy to custom fit your Rescue Mat System to any floor layout.
 |
| | |
Dri-Eaz AirWolf/WolfPack
The AirWolf uses an unbeatable combination of CFM and static pressure to literally force water out of damaged hardwood floors. The WolfPack system directs the high-velocity airflow of the AirWolf into the flutes between the flooring and the subfloor. | | Injectidry HP 60i
Injectidry's High Pressure drying systems are specifically developed to target high risk areas of hidden moisture such as: walls and ceilings, even those coated with watertight finishes like PVA paint and vinyl wallpaper coverings, double-sheeted fire walls, party walls, sound barriers, insulation, walls behind cabinets and fixtures and floors. |
| | | |
Injectidry HP60FDP
Designed specifically for floor drying. This set-up is extremely quick, easy and efficient for your typical floor drying needs. Increase your capabilities to dry ceilings & walls by purchasing AH-CWK. | | Injectidry VAC-IT Panels
HEPA filter can be set up to process air going into or coming out from beneath cabinets, walls, ceilings and floors. All air is processed before going through the blower in either negative or positive drying modes, thus never contaminating equipment.
|
| | |
Injectidry Direct-It
Used to dry under cabinets, assist HP Systems in drying hardwoods by pushing or pulling. The Direct-It In is placed on the snout of airmovers to blow air into spaces that need drying. The Direct-It is placed on the axial fan, either for negative or positive use.
| | Viking PDS-21 Pressurized Drying System
Makes drying wall cavities easier and less frustrating than before. Perfect for under sinks, behind cabinets and permanent furniture. Its portability makes drying a breezy. All in one containment, allows the operator simple on the go equipment just before a 1/2 inch hole, plug in the end hose and begin drying. An on board plug-off system makes plugging unused tubes simple. |
| | |
Injectidry Silencer
The Silencer is made of ABS plastic and quiets the drying system by about 25%. It takes some of the impeller noise out in addition to attenating the air rush sound. Attaches to the 2 in. OUT trunkline and sets up in seconds. The Silencer attaches to either the main AIR IN or AIR OUT Hoses.
| | Injectidry Interceptor
Injectidry's In-line HEPA filtering system, stops dirt in its tracks....before it contaminates your equipment and the air. This HEPA system is the type of filter specified by Certified Industrial Hygienists and filters out impurities at a rate of 99.97%. It can reduce liability while increasing peace of mind for the mold conscious customer.
|
| | | |
Injectidry Active Hoseline
Upgrade Kits Upgrade your "Original" HP's and cut your setup in half with this package! Add our Active Hoseline Ceiling and Wall Drying Kit to your INJFDP and turn it into a wall and ceiling drying system.
| | Injectidry Water Separator
The Water Separator works to protect your HP 60 blower by preventing bulk water from passing through it when drying in a negative mode. It should be used after the initial vacuuming with a truck mount system to capture the remaining water that could be undetected. Will collect bulk water that my be trapped in ceilings, walls, flors, or cabinets that you are drying. |
| |
Injectidry ADP-9 Scrubber
The Adaptidry Products achieve high efficiency by dispersing intense drying power simultaneously to multiple areas around the room. The ADP-5 & ADP-9 fit 12”, 14”, 16” & 18” rings on a variety of axial fans and air scrubbers increas- ing your drying capability. Create more pressure - positive or negative suction within walls and in some cases without drilling holes, making it more effective than other vent systems. They also work great for drying out sleepered floors (sport courts and gymnasiums) with some set up for pushing and some set up to pull on the sleepered floors. When used with a HEPA air scrubber, it becomes a true HEPA filtration system for filtering contaminants during remediation jobs.
|
